- Change radbeacon frequency archive#
- Change radbeacon frequency software#
- Change radbeacon frequency code#
- Change radbeacon frequency series#
- Change radbeacon frequency zip#
In mental health, these insights can illuminate behavioral patterns, creating exciting opportunities for mental health service providers and their clients to support pattern recognition and problem identification outside of formal sessions. Passive data such as physical activity, Global Positioning System (GPS), interpersonal proximity, and audio recordings can provide valuable insight into the lives of individuals. If the step (b) is not working, we recommend the customer to measure the VBAT voltage waveform using CRO and attach it here.Background: With the growing ubiquity of smartphones and wearable devices, there is an increased potential of collecting passive sensing data in mobile health. If all the above steps are working fine, it is confirmed that the project #50 is designed not for low power optimization and cannot be used for this kit unless it is optimized.
Please use this firmware since there are issues with eddystone firmware available in the set up file. Kindly use this firmware which is attached here, and please check if it is working fine. If it is working fine, it is assured that BLE beacon is working fine.ī) I have attached the simple Eddystone firmware here which is optimized to consume very less power and designed for this beacon. This helps to identify, if there are any problems in solar panel or PMIC connection to BLE device. Once it is installed, please go to the Firmware-> BLE-> Solar BLE sensor, once the project is opened, please program the BLE beacon with this project and check if BLE beacon is working alone. In order to debug this further, could you please try the following steps:Ī) Kindly download the complete setup, available in the below link: So there is no enough light intensity to power the BLE device, or BLE firmware might be consuming lot of power which PMIC can't drive. But when the BLE Beacon is removed, based on the intensity of light, the BLE is powered. When the BLE Beacon is connected to debug board, the VDD supply is powered continuously. When it is not attached to the debug board it no longer broadcasts the URL".įrom the above statement, I understood that the program is working fine. Since it is stated in query, "The device is now broadcasting the URL, but ONLY while the beacon is still attached to the debug board. Here is Cypress's answer and a new program.
Change radbeacon frequency zip#
"Project->Archive Workspace." and select minimal, then just upload the resulting zip file.
Change radbeacon frequency archive#
If you can upload a minimal archive of your workspace, it will help with reviewing the settings/changes you've made to get it working When you have the board connected to the development board, are you running it in debug, or just programming it, and letting it run stand-alone? (without any debug features turned on)Ĭan you make sure you are programming the correct project within the workspace? (There are two: Eddystone_EH_Kit, and Eddystone_Pioneer_Kit)
(Make sure you had the right polarity on the battery you connected to the beacon +, -) If you go under the System settings in the PSoC Creator IDE, and change the "SWD" to "GPIO" for debug pins, does toggling that affect the running of the chip?
Change radbeacon frequency software#
But the debug board works when you flash it with your program, then it must be a difference in software So, assuming that the beacon works alright on battery-power, but then stops working when you flash it with your program.
Change radbeacon frequency series#
Two AA batteries in series would be enough to power it I think I would suggest making sure you set it to "Release" when programming the chip, and then try just powering the board using a separate power supply from the debug board to verify it is a power issue, and not the debug board somehow controlling/clocking it.
Change radbeacon frequency code#
If it is only running while on the debug board, either:Ī) You programmed a debug version of the code into the chip (make sure the program is configured for "Release" at the top of the editor)ī) The solar cell hasn't collected enough power to charge the battery on-board in order to send beacon dataĬ) The chip is running full-blast, and is using power faster than it can charge, leading to it having issues broadcasting An unused variable warning is not important, it just says that you aren't using the variable mentioned (in this case, you probably aren't checking a return value from a cyble function).Įventparam is a generic variable to pass data to your application from the cypress BLE stack, so it depends on what your code is running.
0 kommentar(er)
